RetroBrew Computers Forum: General Discussion » 3d printed case design for the MiniMax 8085

Home » RBC Forums » General Discussion » 3d printed case design for the MiniMax 8085 (3d case)

Show: Today's Messages :: Show Polls :: Message Navigator

3d printed case design for the MiniMax 8085 [message #5914]

Sat, 02 February 2019 13:33

djmartins
Messages: 40
Registered: February 2018

Member

I have posted a case for the MiniMax 8085 on thingiverse for people to use.
If there is a need I can print some at reasonable prices for people.

Here is where you can see it:
www.thingiverse.com/thing:3399973

quick print to test so the front cover is a bit thin on the surface, thought
and changes open to discussion.

Report message to a moderator

[Message index]

		3d printed case design for the MiniMax 8085 By: djmartins on Sat, 02 February 2019 13:33
		Re: 3d printed case design for the MiniMax 8085 By: gkaufman on Sun, 03 February 2019 10:12
		Re: 3d printed case design for the MiniMax 8085 By: djmartins on Sun, 03 February 2019 12:12
		Re: 3d printed case design for the MiniMax 8085 By: gkaufman on Sun, 03 February 2019 13:21
		Re: 3d printed case design for the MiniMax 8085 By: djmartins on Sun, 03 February 2019 13:29
		Re: 3d printed case design for the MiniMax 8085 By: gkaufman on Sun, 03 February 2019 16:45
		Re: 3d printed case design for the MiniMax 8085 By: djmartins on Sun, 03 February 2019 21:48
		Re: 3d printed case design for the MiniMax 8085 By: tingo on Wed, 06 February 2019 08:04
		Re: 3d printed case design for the MiniMax 8085 By: gkaufman on Wed, 06 February 2019 11:42
		Re: 3d printed case design for the MiniMax 8085 By: djmartins on Thu, 07 February 2019 18:14
		Re: 3d printed case design for the MiniMax 8085 By: b1ackmai1er on Fri, 08 February 2019 19:52
		Re: 3d printed case design for the MiniMax 8085 By: Sergey on Mon, 03 February 2020 14:41
		Re: 3d printed case design for the MiniMax 8085 By: djmartins on Mon, 03 February 2020 16:01
		Re: 3d printed case design for the MiniMax 8085 By: gkaufman on Fri, 07 February 2020 20:24
		Re: 3d printed case design for the MiniMax 8085 By: scruss on Wed, 05 February 2020 18:42
		Re: 3d printed case design for the MiniMax 8085 By: b1ackmai1er on Thu, 06 February 2020 00:03
		Re: 3d printed case design for the MiniMax 8085 By: djmartins on Thu, 06 February 2020 18:55
		Re: 3d printed case design for the MiniMax 8085 By: etchedpixels on Sat, 08 February 2020 13:16
		Re: 3d printed case design for the MiniMax 8085 By: scruss on Sun, 09 February 2020 18:37
		Re: 3d printed case design for the MiniMax 8085 By: Sergey on Mon, 10 February 2020 14:18
		Re: 3d printed case design for the MiniMax 8085 By: djmartins on Mon, 10 February 2020 16:50

Previous Topic:	New Board: ECB OPL2 Sound Card
Next Topic:	3D Printed Enclosure for Zeta SBC

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Mon Sep 29 06:44:03 PDT 2025

Total time taken to generate the page: 0.00674 seconds